smartctl 7.0 2018-12-30 r4883 [FreeBSD 10.3-STABLE amd64] (local build) Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Toshiba 3.5" DT01ACA... Desktop HDD Device Model: TOSHIBA DT01ACA300 Serial Number: 64O43WZGS LU WWN Device Id: 5 000039 ff4de0f24 Firmware Version: MX6OABB0 User Capacity: 3,000,592,982,016 bytes [3.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Fri Mar 27 10:29:49 2020 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x85) Offline data collection activity was aborted by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (21935) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 366) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0 2 Throughput_Performance 0x0005 139 139 054 Pre-fail Offline - 71 3 Spin_Up_Time 0x0007 158 158 024 Pre-fail Always - 317 (Average 407) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 22 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 124 124 020 Pre-fail Offline - 33 9 Power_On_Hours 0x0012 094 094 000 Old_age Always - 46183 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 22 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 29 193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 29 194 Temperature_Celsius 0x0002 240 240 000 Old_age Always - 25 (Min/Max 22/37) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 8 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 5 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 5 occurred at disk power-on lifetime: 46151 hours (1922 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 a0 08 de 3e 0b Error: UNC at LBA = 0x0b3ede08 = 188669448 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 80 48 e8 84 4e 40 00 10:43:18.103 READ FPDMA QUEUED 61 08 40 48 04 21 40 00 10:43:18.103 WRITE FPDMA QUEUED 60 40 38 e8 94 32 40 00 10:43:18.103 READ FPDMA QUEUED 61 08 30 20 b9 ef 40 00 10:43:18.103 WRITE FPDMA QUEUED 61 30 28 68 22 03 40 00 10:43:18.103 WRITE FPDMA QUEUED Error 4 occurred at disk power-on lifetime: 46151 hours (1922 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 a0 08 de 3e 0b Error: UNC at LBA = 0x0b3ede08 = 188669448 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 80 b0 e8 84 4e 40 00 10:43:14.276 READ FPDMA QUEUED 61 08 a8 48 04 21 40 00 10:43:14.276 WRITE FPDMA QUEUED 60 40 a0 e8 94 32 40 00 10:43:14.276 READ FPDMA QUEUED 61 08 98 20 b9 ef 40 00 10:43:14.276 WRITE FPDMA QUEUED 61 30 90 68 22 03 40 00 10:43:14.276 WRITE FPDMA QUEUED Error 3 occurred at disk power-on lifetime: 46151 hours (1922 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 a0 08 de 3e 0b Error: UNC at LBA = 0x0b3ede08 = 188669448 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 40 08 e8 94 32 40 00 10:43:10.458 READ FPDMA QUEUED 61 08 00 20 b9 ef 40 00 10:43:10.458 WRITE FPDMA QUEUED 61 30 f8 68 22 03 40 00 10:43:10.458 WRITE FPDMA QUEUED 61 40 f0 28 b7 09 40 00 10:43:10.458 WRITE FPDMA QUEUED 61 40 e8 28 67 81 40 00 10:43:10.458 WRITE FPDMA QUEUED Error 2 occurred at disk power-on lifetime: 46151 hours (1922 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 a0 08 de 3e 0b Error: WP at LBA = 0x0b3ede08 = 188669448 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 61 30 70 68 22 03 40 00 10:43:06.632 WRITE FPDMA QUEUED 61 40 68 28 b7 09 40 00 10:43:06.632 WRITE FPDMA QUEUED 61 40 60 28 67 81 40 00 10:43:06.632 WRITE FPDMA QUEUED 61 40 58 a8 67 81 40 00 10:43:06.632 WRITE FPDMA QUEUED 61 40 50 68 67 81 40 00 10:43:06.632 WRITE FPDMA QUEUED Error 1 occurred at disk power-on lifetime: 46151 hours (1922 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 a0 08 de 3e 0b Error: UNC at LBA = 0x0b3ede08 = 188669448 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 98 a8 dd 3e 40 00 10:43:02.826 READ FPDMA QUEUED 60 00 90 a8 dc 3e 40 00 10:43:02.826 READ FPDMA QUEUED 60 00 88 a8 db 3e 40 00 10:43:02.824 READ FPDMA QUEUED 60 00 80 a8 da 3e 40 00 10:43:02.823 READ FPDMA QUEUED 60 00 78 a8 d9 3e 40 00 10:43:02.822 READ FPDMA QUEUED SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 46183 - # 2 Extended offline Completed: read failure 20% 46181 - # 3 Short offline Completed without error 00% 46170 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.